Poly Plast Acrylic Wall Putty
Eureka Paints Poly Plast is a co polymer base interior acrylic wall putty, which is compatible & can be easily applied on concrete, plaster, gypsum or POP. The ingredients of Eureka Paints Polt Plast are carefully selected, which consist of best quality Sand, Acrylic Polymers, Minerals, Additives, Anti Bacterial Agents
Key Features
- Eureka Paints Poly Plast is a smooth finish interior wall putty
- It is Fungus & Bacteria resistance
- Can be easily applied with Putty Knife which is useful for consistent coating allover
- No priming required which saves the material & application cost of primer
Substrate Suitability
Being Co polymer base it has a better strength & can be easily applied of surfaces like concrete, plaster, gypsum, POP.
How To Use
Surface Preparation
- Ensure that the surface to be painted is free from loose paint, dust, grease or any such things.
- Any alterations or repairing work specially the electrical chipping work to be done to the wall should be complete before applying the putty.
- The surface should not be wet or damp.
- The surface should not be affected by fungus, algae or moss
Application System
Product | Application Tool |
Thinner | Dilution % (by vol) |
Touch Dry | Recoat* |
Sand the surface with Emery paper 180 and wipe clean with cloth |
|||||
Eureka Paints IWP Interior waterbase Acrylic Primer (Optional) |
Brush, Spray |
Water Water |
60-70% 70-75% |
30 mins 30 mins |
3-4 hrs 3-4 hrs |
1st Coat Eureka Paints Poly Plast Acrylic Putty |
Putty Knife, Spray |
Water Water |
As required |
1hr | 4-6 hrs |
2nd Coat Eureka Paints Poly PlastAcrylic Putty |
Putty Knife, Spray |
Water Water |
As required |
1hr | 4-6 hrs |
Sand down with Emery Paper 180 and wipe clean | |||||
Eureka Paints IWPInterior waterbase acrylic Primer | Brush, Spray |
Water Water |
60-70% 70-75% |
30 mins 30 mins |
3-4 hrs 3-4 hrs |
Sand down with Emery paper 320 and wipe clean | |||||
2 coats of recommended paint system |
* Recoat period is quoted for 25° C at 50% relative humidity - may vary under different conditions.
Technical Data
Covering** | 13 - 16 sft per kg for 2 coats |
Drying Time | Touch Dry 1 Hr | Hard Dry 12 Hrs |
Condition In can | ready to use Paste |
Priming | No priming required before applying POLY PLAST, however one coat of Eureka IWP can be applied above it for better finishing of Paint |
Colour / Finish | Off White / Smooth |
Recommended DFT per coat | 0.5 - 1.00 mm depending on the condition of surface |
Specific Gravity Kg / ltr | 1.60 +/- 0.05 |
Viscosity | 320 |
PH Value | 8 to 9 |
Hardness | 3H |
Shelf Life | 4 months when stored in cool & dry place in original sealed container |
Top Coat | Compatible to all the existing top coating systems (viz. Distemper, Plastic, Luster, etc) |
** Covering mentioned is for application above gypsum, however the actual covering may vary according to the substrate & also depends on the condition of the surface & method of application
Precautions
- Stir well & strain before use
- Thinning is not advisable, however maximum 3% of water can be added for workability
- Do not apply on surface that are subject to continuous seepage or dampness
- Do not apply it in the form of single coat or thick layer application
Pack Sizes & Shade Range
Pack Size Availability: 20kg, 25kg, 30kg HDPE Bag